- #REALTEK 8192CU DRIVER LINUX DRIVERS#
- #REALTEK 8192CU DRIVER LINUX DRIVER#
- #REALTEK 8192CU DRIVER LINUX MAC#
#REALTEK 8192CU DRIVER LINUX DRIVER#
It seems to build the whole driver but at the end I have a lot of undefined functions : (v3.)Ģ- I modified the Makefile to add a new config:ĮXTRA_CFLAGS += -DCONFIG_LITTLE_ENDIAN -DCONFIG_WEXT_PRIVģ- I called the Makefile. So I don't know what's wrong there, possible TI guys can answer, or RTL support also.Ĭan you please tell me what are the big steps that you did to cross-compile the Realtek driver.ġ- I downloaded the sources for RTL8192CU driver on Realtek's website. Tx excessive retries:0 Invalid misc:0 Missed beacon:0ĭrivers looks so: rtl8192_8188CU_linux_v.20110715Ĭhip version: Chip Version ID: VERSION_NORMAL_TSMC_CHIP_92C.įirmware info (your firmware is later): fw_ver=v75, fw_subver=0, sig=0x88c0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Link Quality:0 Signal level:0 Noise level:0 Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated I cann't even scan for other devices, it gives me empty wlan0 scan No any changes in the code, only cross compile options was changed.įor x86 - everything works fine, no problems at all.įor DM368 - I can only setup wlan0 interface, and get info about it.
#REALTEK 8192CU DRIVER LINUX DRIVERS#
Linux drivers taken from CD retailed with dongle. Has anyone reliably used Realtek 8192cu on DM36x EVM? If yes, kindly let us know the steps and also the driver version used. Link_timer_hdl:no beacon while connecting Rtw_select_and_join_from_scanned_queue: candidate: UBNT_BULLET(00:27:22:e2:b5:fa) <=rtw_wx_set_essid, ret ifconfig wlan0 10.0.0.253 netmask survey done event(16) Set_mode = iwconfig wlan0 channel iwconfig wlan0 essid UBNT_BULLET
#REALTEK 8192CU DRIVER LINUX MAC#
MAC Address from REG_MACID = 00:c0:ca:66:09:5eĪDDRCONF(NETDEV_UP): wlan0: link is not iwconfig wlan0 mode managed IQK: RegE94=103 RegE9C=f RegEA4=0 RegEAC=0 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0 Set RF Chip ID to RF_6052 and RF type to 1T1R. => FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMCįirmwareDownload92C accquire FW from embedded image When following logs appear reboot is required to make wifi work again: This solved by re connecting the USB module.
Try_to_join, but select scanning queue fail, to_roaming:1 Try_to_join, but select scanning queue fail, to_roaming:2 Rtl8192c_set_FwJoinBssReport_cmd mstatus(0) Rtw_select_and_join_from_scanned_queue: return _FAIL(candidate = NULL)
It gets disconnected frequently with following error logs:
We are able to cross compile it and make it work but its not working reliably. We are using dvsdk 4.02 with linux kernel 2.6.32 and trying to port USB WIfi module based upon Realtek RTL8192cu chipset.
0 kommentar(er)
